Vehicle Side
Articulating lock n roll weight distributing hitch that attaches to an adjustable height channel on a tow vehicle. Creates a safer and smoother ride by bringing the rear of the vehicle back up and the front down for better control. For use with the Lock N Roll TS603 spring bar and lever assembly. One of the following Lock N Roll Hitches needs to be attached to the trailer in order to use the Lock N Roll weight distribution system: TS502, TS504, TS528, TS506, TS508, TS510, TS530. VS601 consists of the items shown in the loose parts photo. TS602 and the other Lock N Roll parts in these photos are purchased separately.
$559.00
This vehicle side option of Lock N Roll, the worlds best on road off road hitch, has a 2 7/8" wide, four hole channel that fits and bolts directly inside of a standard, 3 inch wide, height adjustement channel. Mounting holes accommodate industry standard 2” hole spacing for 5/8” bolts. Like all Lock N Roll hitches, this hitch is made of strong, alloy steel with a solid 1" diameter bearing and a grease port to ensure a long life for your hitch. This hitch is rated at 11,000 pounds gross trailer weight and 1100 pounds tongue weight. Comes with two grade 5 5/8" bolts and two nylon insert lock nuts.
All units exceed the requirements of SAE standard J684 and are tested by independent labs.
$210.00
Application: 2" x 2" trailer hitch receivers
Maximum gross trailer weight: 11,000 lbs
Maximum tongue weight: 1,100 lbs
The inside width of the channel is 3-1/16". Bracket material is High Strength/Low Alloy ASTM A572 Grade 50. There are 4 sets of holes allowing for 3-positions. Bracket is welded to a 2" sq x 1/4" thick wall x 9-1/2" long tube with 2 sets of receiver pin holes. Tubing is high quality ASTM A500 with a minimum tensile strength of 58,000 PSI and 23% elongation. The maximum height adjustment of the VS 503 VS505 combination is 5-1/2" as measured from the center of the receiver tube to the center of the Lock N Roll coupling shaft on your trailer. The horizontal distances from the 5/8" receiver pin holes to the center of the coupling shaft are 14-1/4 and 16-1/4.
$270.00
Application: 2" x 2" trailer hitch receivers
Maximum gross trailer weight: 11,000 lbs
Maximum tongue weight: 1,100 lbs
The inside width of the channel is 3-1/16". Bracket material is High Strength/Low Alloy ASTM A572 Grade 50. There are 6 sets of holes allowing for 5 positions. Bracket is welded to a 2" sq x 1/4" thick wall x 9-1/2" long tube with 2 sets of receiver pin holes. Tubing is high quality ASTM A500 with a minimum tensile strength of 58,000 PSI and 23% elongation. The maximum height adjustment of the VS 503 VS505 combination is 9-1/2" as measured from the center of the receiver tube to the center of the Lock N Roll coupling shaft on your trailer. The horizontal distances from the 5/8" receiver pin holes to the center of the coupling shaft are 14-1/4 and 16-1/4.
$290.00
Application: 2" x 2" trailer hitch receivers
Maximum gross trailer weight: 11,000 lbs
Maximum tongue weight: 1,100 lbs
The inside width of the channel is 3-1/16". Bracket material is High Strength/Low Alloy ASTM A572 Grade 50. There are 6 sets of holes allowing for 5 positions. Bracket is welded to a 2" sq x 1/4" thick wall x 15" long tube with 2 sets of receiver pin holes. Tubing is high quality ASTM A500 with a minimum tensile strength of 58,000 PSI and 23% elongation. The maximum height adjustment of the VS 503 VS519 combination is 5-1/2" as measured from the center of the receiver tube to the center of the Lock N Roll coupling shaft on your trailer. The horizontal distances from the 5/8" receiver pin holes to the center of the coupling shaft are 19-3/4 and 21-3/4.
$289.00
This vehicle side option of Lock N Roll slides directly into a standard 2" reciever tube. It can be set 2-1/2" higher or lower than the reciever tube. Like all Lock N Roll hitches, this hitch is made of strong, alloy steel with a solid, 1" inch diameter bearing and a grease port to ensure a long life for your hitch. This hitch is rated at 11,000 pounds gross trailer weight and 1100 pounds tongue weight. All units exceed the requirements of SAE standard J684 and are tested by independent labs.
$209.00
Hitch on 1-1/4" square bar. 3500 pounds MGTW, 350 pounds Max Tongue weight
$170.00
11-3/4" tall adjustable height channel bracket. Bracket material is High Strength/Low Alloy ASTM A572 Grade 50. There are 6 sets of holes allowing for 5-positions. Bracket is welded to a 2" sq x 1/4" thick wall x 9-1/2" long tube. Tubing is high quality ASTM A500 with a minimum tensile strength of 58,000 PSI and 23% elongation. The maximum height adjustment when used with PN 503 is 8-1/2" measured from the center of the receiver tube to the center of the Lock N Roll coupling shaft on your trailer.
$87.00
This vehicle side option of Lock N Roll slides directly into a standard 2" receiver tube. It can be set 4" higher or lower than the receiver tube. Like all Lock N Roll hitches, this hitch is made of strong, alloy steel with a solid, 1" inch diameter bearing and a grease port to ensure a long life for your hitch. This hitch is rated at 11,000 pounds gross trailer weight and 1100 pounds tongue weight. All units exceed the requirements of SAE standard J684 and are tested by independent labs.
$216.00
NSN:5340-00-456-1011 Mil Spec lashing hook for securing tarps and equipment on trailers and trucks.
Minimum order is 6 hooks.
Holes are 1-1/8" center to center and 11/32" diameter.
$7.35
1/2" diameter hitch pin made for securing the Lock N Roll latch plates. Your Lock N Roll vehicle hitch comes with one but it doesn't hurt to have a spare.
Included with the 1/2" diameter pin is a cotter pin.
$5.71
This is designed to get out past the spare tire on Jeeps and SUVs. Must be used with PN503. Maximum gross trailer weight of 4500 pounds.
$86.00
This vehicle side option of Lock N Roll, the worlds best on road, off road hitch, slides directly into a standard 2" square receiver tube . Like all of our hitches, it's made of strong, alloy steel and a solid 1" bearing with a grease port to ensure a long life for your hitch. This hitch is rated at 11,000 pounds gross trailer weight and 1100 pounds tongue weight. All units exceed the requirements of SAE standard J684 and are tested by independent labs.
$217.00
8" tall adjustable height channel bracket. This can be used with Lock N Roll TS502 or VS503 or any other manufacturer's equipment. The inside width of the channel is 3-1/16". Bracket material is High Strength/Low Alloy ASTM A572 Grade 50. There are 4 sets of holes allowing for 3-positions. Bracket is welded to a 2" sq x 1/4" thick wall x 9-1/2" long tube. Tubing is high quality ASTM A500 with a minimum tensile strength of 58,000 PSI and 23% elongation. The maximum height adjustment when used with VS 503 is 5-1/2" measured from the center of the receiver tube to the center of the Lock N Roll coupling shaft on your trailer. The horizontal distances from the 5/8" receiver pin holes to the center of the coupling shaft are 14-1/4 and 16-1/4.
$67.00
8 hole height adjustment channel on1-1/4" bar for use with PN 503 on your vehicle or PN 502 on your trailer. Inside of channel is 3" wide and 1-3/4" deep.
$47.00
Showing 1 to 15 of 15 (1 Pages)
